DragonFly On-Line Manual Pages

ipmitool(1) ipmitool(1)

NAME
ipmitool - utility for controlling IPMI-enabled devices

SYNOPSIS
ipmitool [ <options> ] <command> [ <sub-commands and sub-options> ]

<options> := [ <general-options> | <conditional-opts> ]
Any recognized option is accepted. Conditional options may be ignored
or it's usage postponed until shell or exec processes relevant command.

<conditional-opts> := [ <lan-options> | <lanplus-options> |
<command-options> ]
Bridging:
<bridge-options> := -t <target_address> [ -b <channel> |
[ -T <address> | -B <channel> ] ]

Options used with -I lan:
<lan-options> := [ -A <authtype> ]

Options used with -I lanplus:
<lanplus-options> := [ -C <ciphersuite> | <key-option> ]

Option groups setting same value:
<key-option> := [ -k <key> | -K | -y <hex_key> | -Y ]
<password-option> := [ -f <password_file> | -a | -P <password> | -E ]
<oem-option> := [ -o <oemtype> | -g | -s ]

Options used with specific command <command-options>:
<options-sdr> := [ -S <sdr_cache_file> ]
<options-sel> := [ -O <sel_oem> ]
<options-sol> := [ -e <sol_escape_char> ]

DESCRIPTION
This program lets you manage Intelligent Platform Management Interface
(IPMI) functions of either the local system, via a kernel device
driver, or a remote system, using IPMI v1.5 and IPMI v2.0. These
functions include printing FRU information, LAN configuration, sensor
readings, and remote chassis power control.

IPMI management of a local system interface requires a compatible IPMI
kernel driver to be installed and configured. On Linux this driver is
called OpenIPMI and it is included in standard distributions. On
Solaris this driver is called BMC and is included in Solaris 10.
Management of a remote station requires the IPMI-over-LAN interface to
be enabled and configured. Depending on the particular requirements of
each system it may be possible to enable the LAN interface using
ipmitool over the system interface.

OPTIONS
-a Prompt for the remote server password.

-A <authtype>
Specify an authentication type to use during IPMIv1.5 lan
session activation. Supported types are NONE, PASSWORD, MD2,
MD5, or OEM.

-b <channel>
Set destination channel for bridged request.

-B <channel>
Set transit channel for bridged request (dual bridge).

-b <channel>
Set destination channel for bridged request.

-B <channel>
Set transit channel for bridged request. (dual bridge)

-c Present output in CSV (comma separated variable) format. This
is not available with all commands.

-C <ciphersuite>
The remote server authentication, integrity, and encryption
algorithms to use for IPMIv2.0 lanplus connections. See table
22-19 in the IPMIv2.0 specification. The default is 3 which
specifies RAKP-HMAC-SHA1 authentication, HMAC-SHA1-96 integrity,
and AES-CBC-128 encryption algorithms.

-d N Use device number N to specify the /dev/ipmiN (or /dev/ipmi/N or
/dev/ipmidev/N) device to use for in-band BMC communication.
Used to target a specific BMC on a multi-node, multi-BMC system
through the ipmi device driver interface. Default is 0.

-e <sol_escape_char>
Use supplied character for SOL session escape character. The
default is to use ~ but this can conflict with ssh sessions.

-E The remote server password is specified by the environment
variable IPMI_PASSWORD or IPMITOOL_PASSWORD. The
IPMITOOL_PASSWORD takes precedence.

-f <password_file>
Specifies a file containing the remote server password. If this
option is absent, or if password_file is empty, the password
will default to NULL.

-g Deprecated. Use: -o intelplus

-h Get basic usage help from the command line.

-H <address>
Remote server address, can be IP address or hostname. This
option is required for lan and lanplus interfaces.

-I <interface>
Selects IPMI interface to use. Supported interfaces that are
compiled in are visible in the usage help output.

-k <key>
Use supplied Kg key for IPMIv2.0 authentication. The default is
not to use any Kg key.

-K Read Kg key from IPMI_KGKEY environment variable.

-l <lun>
Set destination lun for raw commands.

-L <privlvl>
Force session privilege level. Can be CALLBACK, USER, OPERATOR,
ADMINISTRATOR. Default is ADMINISTRATOR. This value is ignored
and always set to ADMINISTRATOR when combined with -t target
address.

-m <local_address>
Set the local IPMB address. The local address defaults to 0x20
or is auto discovered on PICMG platforms when -m is not
specified. There should be no need to change the local address
for normal operation.

-N <sec>
Specify nr. of seconds between retransmissions of lan/lanplus
messages. Defaults are 2 seconds for lan and 1 second for
lanplus interfaces. Command raw uses fixed value of 15 seconds.
Command sol uses fixed value of 1 second.

-o <oemtype>
Select OEM type to support. This usually involves minor hacks
in place in the code to work around quirks in various BMCs from
various manufacturers. Use -o list to see a list of current
supported OEM types.

-O <sel oem>
Open selected file and read OEM SEL event descriptions to be
used during SEL listings. See examples in contrib dir for file
format.

-p <port>
Remote server UDP port to connect to. Default is 623.

-P <password>
Remote server password is specified on the command line. If
supported it will be obscured in the process list. Note!
Specifying the password as a command line option is not
recommended.

-R <count>
Set the number of retries for lan/lanplus interface (default=4).
Command raw uses fixed value of one try (no retries). Command
hpm uses fixed value of 10 retries.

-s Deprecated. Use: -o supermicro

-S <sdr_cache_file>
Use local file for remote SDR cache. Using a local SDR cache
can drastically increase performance for commands that require
knowledge of the entire SDR to perform their function. Local
SDR cache from a remote system can be created with the sdr dump
command.

-t <target_address>
Bridge IPMI requests to the remote target address. Default is
32. The -L privlvl option is always ignored and value set to
ADMINISTRATOR.

-T <address>
Set transit address for bridge request (dual bridge).

-T <transmit_address>
Set transit address for bridge request. (dual bridge)

-U <username>
Remote server username, default is NULL user.

-v Increase verbose output level. This option may be specified
multiple times to increase the level of debug output. If given
three times you will get hexdumps of all incoming and outgoing
packets. Using it five times provides details on request and
expected reply procesing. The hpm commands targetcap compprop
abort upgstatus rollback rollbackstatus selftestresult increases
the verbosity level

-V Display version information.

-y <hex key>
Use supplied Kg key for IPMIv2.0 authentication. The key is
expected in hexadecimal format and can be used to specify keys
with non-printable characters. E.g. '-k PASSWORD' and '-y
50415353574F5244' are equivalent. The default is not to use any
Kg key.

-Y Prompt for the Kg key for IPMIv2.0 authentication.

-z <size>
Change Size of Communication Channel. (OEM)

If no password method is specified then ipmitool will prompt the user
for a password. If no password is entered at the prompt, the remote
server password will default to NULL.

SECURITY
There are several security issues be be considered before enabling the
IPMI LAN interface. A remote station has the ability to control a
system's power state as well as being able to gather certain platform
information. To reduce vulnerability it is strongly advised that the
IPMI LAN interface only be enabled in 'trusted' environments where
system security is not an issue or where there is a dedicated secure
'management network'.

Further it is strongly advised that you should not enable IPMI for
remote access without setting a password, and that that password should
not be the same as any other password on that system.

When an IPMI password is changed on a remote machine with the IPMIv1.5
lan interface the new password is sent across the network as clear
text. This could be observed and then used to attack the remote
system. It is thus recommended that IPMI password management only be
done over IPMIv2.0 lanplus interface or the system interface on the
local station.

For IPMI v1.5, the maximum password length is 16 characters. Passwords
longer than 16 characters will be truncated.

For IPMI v2.0, the maximum password length is 20 characters; longer
passwords are truncated.

COMMANDS
help This can be used to get command-line help on ipmitool
commands. It may also be placed at the end of commands to get
option usage help.

ipmitool help
Commands:
bmc Deprecated. Use mc
channel Configure Management Controller channels
chassis Get chassis status and set power state
dcmi Data Center Management Interface
delloem Manage Dell OEM Extensions.
echo Used to echo lines to stdout in scripts
ekanalyzer run FRU-Ekeying analyzer using FRU files
event Send events to MC
exec Run list of commands from file
firewall Configure Firmware Firewall
fru Print built-in FRU and scan for FRU
locators
fwum Update IPMC using Kontron OEM Firmware
Update Manager
gendev Read/Write Device associated with Generic
Device locators sdr
hpm Update HPM components using PICMG HPM.1
file
i2c Send an I2C Master Write-Read command and
print response
ime Upgrade/Query Intel ME firmware
isol Configure and connect Intel IPMIv1.5
Serial-over-LAN
kontronoem Manage Kontron OEM Extensions
lan Configure LAN Channels
mc Management Controller status and global
enables
nm Node Manager
pef Configure Platform Event Filtering (PEF)
picmg Run a PICMG/ATA extended command
power Shortcut to chassis power commands
raw Send a RAW IPMI request and print response
sdr Print Sensor Data Repository entries and
readings
sel Print System Event Log (SEL)
sensor Print detailed sensor information
session Print session information
set Set runtime variable for shell and exec
shell Launch interactive IPMI shell
sol Configure and connect IPMIv2.0
Serial-over-LAN
spd Print SPD info from remote I2C device
sunoem Manage Sun OEM Extensions
tsol Configure and connect Tyan IPMIv1.5
Serial-over-LAN
user Configure Management Controller users

channel

authcap <channel number> <max priv>

Displays information about the authentication
capabilities of the selected channel at the specified
privilege level.

Possible privilege levels are:
1 Callback level
2 User level
3 Operator level
4 Administrator level
5 OEM Proprietary level
15 No access

info [channel number]

Displays information about the selected channel. If
no channel is given it will display information about the
currently used channel.

> ipmitool channel info
Channel 0xf info:
Channel Medium Type : System Interface
Channel Protocol Type : KCS
Session Support : session-less
Active Session Count : 0
Protocol Vendor ID : 7154

getaccess <channel number> [<userid>]

Configure the given userid as the default on the given
channel number. When the given channel is subsequently
used, the user is identified implicitly by the given
userid.

setaccess <channel number> <userid> [<callin=on|off>]
[<ipmi=on|off>] [<link=on|off>]
[<privilege=level>]

Configure user access information on the given
channel for the given userid.

getciphers <ipmi|sol> [<channel>]

Displays the list of cipher suites supported for
the given application (ipmi or sol) on the given
channel.

chassis

status

Status information related to power, buttons, cooling,
drives and faults.

power

status

off

cycle

reset

diag

soft

identify [<seconds>|force]

Identify interval.
Default is 15 seconds.
0 - Off
force - To turn on indefinitely

policy

What to do when power is restored.

list

Show available options.

always-on

always-off

restart_cause

Last restart cause.

poh

Get power on hours.

bootdev

none

Do not change boot device order.

pxe

Force PXE boot.

disk

Force boot from default Hard-drive.

safe

Force boot from default Hard-drive, request Safe
Mode.

diag

Force boot from Diagnostic Partition.

cdrom

Force boot from CD/DVD.

bios

Force boot into BIOS Setup.

floppy

Force boot from Floppy/primary removable media.

bootparam

force_pxe

Force PXE boot

force_disk

Force boot from default Hard-drive

force_safe

Force boot from default Hard-drive, request Safe
Mode

force_diag

Force boot from Diagnostic Partition

force_cdrom

Force boot from CD/DVD

force_bios

Force boot into BIOS Setup

selftest

dcmi

discover

This command is used to discover supported capabilities
in DCMI.

power <command>

Platform power limit command options are:

reading

Get power related readings from the system.

get_limit

Get the configured power limits.

set_limit <parameter> <value>

Set a power limit option.

Possible parameters/values are:

action <No Action | Hard Power Off & Log Event to
SEL | Log Event to SEL>

Exception Actions are taken as "No Action",
"Hard Power Off system and log events to
SEL", or "Log event to SEL only".

limit <number in Watts>

Power Limit Requested in Watts.

correction <number in milliseconds>

Correction Time Limit in milliseconds.

sample <number in seconds>

Statistics Sampling period in seconds.

activate

Activate the set power limit.

deactivate

Deactivate the set power limit.

sensors

Prints the available DCMI sensors.

asset_tag

Prints the platforms asset tag.

set_asset_tag <string>

Sets the platforms asset tag

get_mc_id_string

Get management controller identifier string.

set_mc_id_string <string>

Set management controller identifier string. The maximum
length is 64 bytes including a null terminator.

thermalpolicy [<get | set>]

Thermal Limit policy get/set.

The commands are:

Get <entityID> <instanceID>

Get Thermal Limit values.

entityID is the physical entity that a sensor or
device is associated with. instanceID is a
particular instance of an entity. Entity Instance
can be in one of two ranges, system-relative or
device-relative. For example, a system with four
processors could use an Entity Instance value of
"0" to identify the first processor.

Set <entityID> <instanceID>

Set Thermal Limit values.

get_temp_reading

Get Temperature Sensor Readings.

get_conf_param

Get DCMI Configuration Parameters.

set_conf_param <parameters>

Set DCMI Configuration Parameters.

The Configuration Parameters are:

activate_dhcp

Activate/restart DHCP

dhcp_config

Discover DHCP Configuration.

init

Set DHCP Initial timeout interval, in seconds.
The recommended default is four seconds.

timeout

Set DHCP Server contact timeout interval, in
seconds. The recommended default timeout is two
minutes.

retry

Set DHCP Server contact retry interval, in
seconds. The recommended default timeout is
sixty-four seconds.

oob_discover

Ping/Pong Message for DCMI Discovery.

delloem

The delloem commands provide information on Dell-specific
features.

setled {b:d.f} {state..}

Sets the drive backplane LEDs for a device.
{b:d.f} = PCI Address of device (eg. 06:00.0)
{state} = one or more of the following:
online | present | hotspare | identify |
rebuilding | fault | predict | critical | failed

lcd
set {mode}|{lcdqualifier}|{errordisplay}

Allows you to set the LCD mode and user-defined
string.

lcd set mode
{none}|{modelname}|{ipv4address}|{macaddress}|
{systemname}|{servicetag}|{ipv6address}|
{ambienttemp}|{systemwatt}|{assettag}|
{userdefined}<text>

Allows you to set the LCD display mode to any of
the preceding parameters.

lcd set lcdqualifier
{watt}|{btuphr}|
{celsius}|{fahrenheit}

Allows you to set the unit for the system ambient
temperature mode.

lcd set errordisplay
{sel}|{simple}

Allows you to set the error display.

lcd info

Displays the LCD screen information.

lcd set vkvm
{active}|{inactive}

Allows you to set the vKVM status to active or
inactive. When it is active and session is in
progress, a message appears on LCD.

lcd status

Displays the LCD status for vKVM display active or
inactive and Front Panel access mode
(viewandmodify, view-only or disabled).

mac

Displays the information about the system NICs.

mac list

Displays the NIC MAC address and status of all
NICs. It also displays the DRAC/iDRAC MAC address.

mac get
<NIC number>

Displays the selected NICs MAC address and status.

lan
Displays the information of Lan.

lan set
<Mode>

Sets the NIC selection mode (dedicated, shared
with lom1, shared with lom2,shared with
lom3,shared with lom4,shared with failover
lom1,shared with failover lom2,shared with
failover lom3,shared with failover lom4,shared
with Failover all loms, shared with Failover
None).

lan get

Returns the current NIC selection mode (dedicated,
shared with lom1, shared with lom2, shared with
lom3, shared with lom4,shared with failover lom1,
shared with failover lom2,shared with failover
lom3,shared with failover lom4,shared with
Failover all loms,shared with Failover None).

lan get active

Returns the current active NIC (dedicated, LOM1,
LOM2, LOM3 or LOM4).

powermonitor

Displays power tracking statistics.

powermonitor clear cumulativepower

Reset cumulative power reading.

powermonitor clear peakpower

Reset peak power reading.

powermonitor powerconsumption
<watt>|<btuphr>
Displays the power consumption in watt or btuphr.

powermonitor powerconsumptionhistory
<watt>|<btuphr>
Displays the power consumption history in watt or
btuphr.

powermonitor getpowerbudget
<watt>|<btuphr>
Displays the power cap in watt or btuphr.

powermonitor setpowerbudget
<val><watt|btuphr|percent>
Allows you to set the power cap in watt, BTU/hr
or percentage.

powermonitor enablepowercap
Enables set power cap.

powermonitor disablepowercap

Disables set power cap.

vFlash info Card

Shows Extended SD Card information.

echo

For echoing lines to stdout in scripts.

ekanalyzer <command> <xx=filename1> <xx=filename2> [<rc=filename3>] ...
NOTE : This command can support a maximum of 8 files per command
line
filename1 : binary file that stores FRU data of a Carrier or an
AMC module
filename2 : binary file that stores FRU data of an AMC module.
These binary files can be generated from command:
ipmitool fru read <id> <filename>
filename3 : configuration file used for configuring On-Carrier
Device ID or OEM GUID. This file is optional.
xx : indicates the type of the file. It can take the following
value:
oc : On-Carrier device
a1 : AMC slot A1
a2 : AMC slot A2
a3 : AMC slot A3
a4 : AMC slot A4
b1 : AMC slot B1
b2 : AMC slot B2
b3 : AMC slot B3
b4 : AMC slot B4
sm : Shelf Manager

The available commands for ekanalyzer are:

print [<carrier | power | all>]

carrier (default) <oc=filename1> <oc=filename2> ...

Display point to point physical connectivity
between carriers and AMC modules.
Example:
> ipmitool ekanalyzer print carrier oc=fru
oc=carrierfru
From Carrier file: fru
Number of AMC bays supported by Carrier: 2
AMC slot B1 topology:
Port 0 =====> On Carrier Device ID 0,
Port 16
Port 1 =====> On Carrier Device ID 0,
Port 12
Port 2 =====> AMC slot B2, Port 2
AMC slot B2 topology:
Port 0 =====> On Carrier Device ID 0,
Port 3
Port 2 =====> AMC slot B1, Port 2
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
From Carrier file: carrierfru
On Carrier Device ID 0 topology:
Port 0 =====> AMC slot B1, Port 4
Port 1 =====> AMC slot B1, Port 5
Port 2 =====> AMC slot B2, Port 6
Port 3 =====> AMC slot B2, Port 7
AMC slot B1 topology:
Port 0 =====> AMC slot B2, Port 0
AMC slot B1 topology:
Port 1 =====> AMC slot B2, Port 1
Number of AMC bays supported by Carrier: 2

power <xx=filename1> <xx=filename2> ...

Display power supply information between carrier
and AMC modules.

all <xx=filename> <xx=filename> ...

Display both physical connectivity and power
supply of each carrier and AMC modules.

frushow <xx=filename>
Convert a binary FRU file into human readable text
format. Use -v option to get more display information.

summary [<match | unmatch | all>]

match (default) <xx=filename> <xx=filename> ...
Display only matched results of Ekeying match
between an On-Carrier device and an AMC module or
between 2 AMC modules. Example:
> ipmitool ekanalyzer summary match oc=fru
b1=amcB1 a2=amcA2
On-Carrier Device vs AMC slot B1
AMC slot B1 port 0 ==> On-Carrier Device 0 port
16
Matching Result
- From On-Carrier Device ID 0
-Channel ID 11 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
- To AMC slot B1
-Channel ID 0 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
AMC slot B1 port 1 ==> On-Carrier Device 0 port
12
Matching Result
- From On-Carrier Device ID 0
-Channel ID 6 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
- To AMC slot B1
-Channel ID 1 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
On-Carrier Device vs AMC slot A2
AMC slot A2 port 0 ==> On-Carrier Device 0 port
3
Matching Result
- From On-Carrier Device ID 0
-Channel ID 9 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
- To AMC slot A2
-Channel ID 0 || Lane 0: enable
-Link Type: AMC.2 Ethernet
-Link Type extension: 1000BASE-BX (SerDES
Gigabit) Ethernet link
-Link Group ID: 0 || Link Asym. Match: exact
match
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
AMC slot B1 vs AMC slot A2
AMC slot A2 port 2 ==> AMC slot B1 port 2
Matching Result
- From AMC slot B1
-Channel ID 2 || Lane 0: enable
-Link Type: AMC.3 Storage
-Link Type extension: Serial Attached SCSI
(SAS/SATA)
-Link Group ID: 0 || Link Asym. Match: FC or
SAS interface {exact match}
- To AMC slot A2
-Channel ID 2 || Lane 0: enable
-Link Type: AMC.3 Storage
-Link Type extension: Serial Attached SCSI
(SAS/SATA)
-Link Group ID: 0 || Link Asym. Match: FC or
SAS interface {exact match}
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*

unmatch <xx=filename> <xx=filename> ...

Display the unmatched results of Ekeying match
between an On-Carrier device and an AMC module or
between 2 AMC modules

all <xx=filename> <xx=filename> ...

Display both matched result and unmatched results
of Ekeying match between two cards or two modules.

event

Send a pre-defined test event to the System Event Log.
The following events are included as a means to test the
functionality of the System Event Log component of the
BMC (an entry will be added each time the event N command
is executed).

Currently supported values for N are:
1 Temperature: Upper Critical: Going High
2 Voltage Threshold: Lower Critical: Going Low
3 Memory: Correctable ECC

NOTE: These pre-defined events will likely not produce
"accurate" SEL records for a particular system because
they will not be correctly tied to a valid sensor number,
but they are sufficient to verify correct operation of
the SEL.

file <filename>

Event log records specified in <filename> will be added
to the System Event Log.

The format of each line in the file is as follows:

<{EvM Revision} {Sensor Type} {Sensor Num} {Event
Dir/Type} {Event Data 0} {Event Data 1} {Event Data 2}>[#
COMMENT]

e.g.: 0x4 0x2 0x60 0x1 0x52 0x0 0x0 # Voltage threshold:
Lower Critical: Going Low

EvM Revision - The "Event Message Revision" is 0x04 for
messages that comply with the IPMI 2.0 Specification and
0x03 for messages that comply with the IPMI 1.0
Specification.

Sensor Type - Indicates the Event Type or Class.

Sensor Num - Represents the 'sensor' within the
management controller that generated the Event Message.

Event Dir/Type - This field is encoded with the event
direction as the high bit (bit 7) and the event type as
the low 7 bits. Event direction is 0 for an assertion
event and 1 for a deassertion event.

See the IPMI 2.0 specification for further details on the
definitions for each field.

Get a list of all the possible Sensor States and pre-
defined Sensor State Shortcuts available for a particular
sensor. sensorid is the character string representation
of the sensor and must be enclosed in double quotes if it
includes white space. Several different commands
including ipmitool sensor list may be used to obtain a
list that includes the sensorid strings representing the
sensors on a given system.

> ipmitool -I open event "PS 2T Fan Fault" list
Finding sensor PS 2T Fan Fault... ok
Sensor States:
State Deasserted
State Asserted
Sensor State Shortcuts:
present absent
assert deassert
limit nolimit
fail nofail
yes no
on off
up down

<sensorid> <sensor state> [<direction>]

Generate a custom event based on existing sensor
information. The optional event direction can be either
assert (the default) or deassert.

> ipmitool event "PS 2T Fan Fault" "State Asserted"
Finding sensor PS 2T Fan Fault... ok
0 | Pre-Init Time-stamp | Fan PS 2T Fan Fault |
State Asserted

> ipmitool event "PS 2T Fan Fault" "State Deasserted"
Finding sensor PS 2T Fan Fault... ok
0 | Pre-Init Time-stamp | Fan PS 2T Fan Fault |
State Desserted

exec <filename>

Execute ipmitool commands from filename. Each line is a
complete command. The syntax of the commands are defined by the
COMMANDS section in this manpage. Each line may have an
optional comment at the end of the line, delimited with a `#'
symbol.

e.g., a command file with two lines:

sdr list # get a list of sdr records
sel list # get a list of sel records

firewall

This command supports the Firmware Firewall capability. It may
be used to add or remove security-based restrictions on certain
commands/command sub-functions or to list the current firmware
firewall restrictions set on any commands. For each firmware
firewall command listed below, parameters may be included to
cause the command to be executed with increasing granularity on
a specific LUN, for a specific NetFn, for a specific IPMI
Command, and finally for a specific command's sub-function (see
Appendix H in the IPMI 2.0 Specification for a listing of any
sub-function numbers that may be associated with a particular
command).

Parameter syntax and dependencies are as follows:

[<channel H>] [<lun L> [ <netfn N> [<command C [<subfn S>]]]]

Note that if "netfn <N>" is specified, then "lun <L>" must also
be specified; if "command <C>" is specified, then "netfn <N>"
(and therefore "lun <L>") must also be specified, and so forth.

"channel <H>" is an optional and standalone parameter. If not
specified, the requested operation will be performed on the
current channel. Note that command support may vary from
channel to channel.

Firmware firewall commands:

info [<Parms as described above>]

List firmware firewall information for the specified LUN,
NetFn, and Command (if supplied) on the current or
specified channel. Listed information includes the
support, configurable, and enabled bits for the specified
command or commands.

Some usage examples:

info [<channel H>] [<lun L>]

This command will list firmware firewall
information for all NetFns for the specified LUN
on either the current or the specified channel.

info [<channel H>] [<lun L> [ <netfn N> ]

This command will print out all command
information for a single LUN/NetFn pair.

info [<channel H>] [<lun L> [ <netfn N> [<command C] ]]

This prints out detailed, human-readable
information showing the support, configurable, and
enabled bits for the specified command on the
specified LUN/NetFn pair. Information will be
printed about each of the command subfunctions.

info [<channel H>] [<lun L> [ <netfn N> [<command C
[<subfn S>]]]]

Print out information for a specific sub-function.

enable [<Parms as described above>]

This command is used to enable commands for a given
NetFn/LUN combination on the specified channel.

disable [<Parms as described above>] [force]

This command is used to disable commands for a given
NetFn/LUN combination on the specified channel. Great
care should be taken if using the "force" option so as
not to disable the "Set Command Enables" command.

reset [<Parms as described above>]

This command may be used to reset the firmware firewall
back to a state where all commands and command sub-
functions are enabled.

fru

Read all Field Replaceable Unit (FRU) inventory data
and extract such information as serial number, part
number, asset tags, and short strings describing the
chassis, board, or product.

read <fru id> <fru file>

fru id is the digit ID of the FRU (see output of 'fru
print'). fru file is the absolute pathname of a file in
which to dump the binary FRU data pertaining to the
specified FRU entity.

write <fru id> <fru file>

fru id is the digit ID of the FRU (see output of 'fru
print'). fru file is the absolute pathname of a file
from which to pull the binary FRU data before uploading
it to the specified FRU.

upgEkey <fru id> <fru file>

Update a multirecord FRU location. fru id is the digit
ID of the FRU (see output of 'fru print'). fru file is
the absolute pathname of a file from which to pull the
binary FRU data to upload into the specified multirecord
FRU entity.

edit <fru id>

This command provides interactive editing of some
supported records, namely PICMG Carrier Activation
Record. fru id is the digit ID of the FRU (see output of
'fru print'); default is 0.

edit <fru id> field <section> <index> <string>

This command may be used to set a field string to a new
value. It replaces the FRU data found at index in the
specified section with the supplied string.

fru id is the digit ID of the FRU (see output of 'fru
print').

<section> is a string which refers to FRU Inventory
Information
Storage Areas and may be refer to:

c FRU Inventory Chassis Info Area

b FRU Inventory Board Info Area

p FRU Inventory Product Info Area

<index> specifies the field number. Field numbering
starts on the first 'english text' field type. For
instance in the <board> info area field '0' is <Board
Manufacturer> and field '2' is <Board Serial Number>; see
IPMI Platform Management FRU Information Storage
Definition v1.0 R1.1 for field locations.

<string> must be the same length as the string being
replaced and must be 8-bit ASCII (0xCx).

edit <fru id> oem iana <record> <format> [<args>]

This command edits the data found in the multirecord
area. Support for OEM specific records is limited.

fwum
Update IPMC using Kontron OEM Firmware Update Manager.

info
Show information about current firmware.

status
Show status of each firmware bank present in the
hardware.

download <filename>

Download specified firmware.

upgrade [filename]

Install firmware upgrade. If the filename is specified,
the file is downloaded first, otherwise the last firmware
downloaded is used.

rollback

Ask IPMC to rollback to previous version.

tracelog

Show firmware upgrade log.

gendev

list

List All Generic Device Locators.

read <sdr name> <file>

Read to file eeprom specify by Generic Device Locators.

write <sdr name> <file>

Write from file eeprom specify by Generic Device Locators

hpm
PICMG HPM.1 Upgrade Agent

check
Check the target information.

check <filename>
Display both the existing target version and image
version on the screen.

download <filename>

Download specified firmware.

upgrade <filename> [all] [component <x>] [activate]
Upgrade the firmware using a valid HPM.1 image file. If
no option is specified, the firmware versions are checked
first and the firmware is upgraded only if they are
different.

all
Upgrade all components even if the firmware
versions are the same (use this only after using
"check" command).

component <x>
Upgrade only given component from the given file.
component 0 - BOOT
component 1 - RTK

activate
Activate new firmware right away.

activate

Activate the newly uploaded firmware.

targetcap

Get the target upgrade capabilities.

compprop <id> <select>
Get the specified component properties. Valid component
id: 0-7. Select can be one of following:
0 - General properties
1 - Current firmware version
2 - Description string
3 - Rollback firmware version
4 - Deferred firmware version

abort

Abort the on-going firmware upgrade.

upgstatus
Show status of the last long duration command.

rollback
Perform manual rollback on the IPM Controller firmware.

rollbackstatus

Show the rollback status.

selftestresult

Query the self test results.

i2c <i2caddr> <read bytes> [<write data>]

This command may be used to execute raw I2C commands with the
Master Write-Read IPMI command.

ime

help

Print usage information

info

Displays information about the Manageability Engine (ME)

update <file>

Upgrade the ME firmware with the specified image file
WARNING You MUST use a supported image provided by your
board vendor

rollback

Perform manual rollback of the ME firmware

isol

info

Retrieve information about the Intel IPMI v1.5
Serial-Over-LAN configuration.

set <parameter> <value>

Configure parameters for Intel IPMI v1.5 Serial-over-LAN.

Valid parameters and values are:

enabled
true, false.

privilege-level
user, operator, admin, oem.

bit-rate
9.6, 19.2, 38.4, 57.6, 115.2.

activate

Causes ipmitool to enter Intel IPMI v1.5 Serial Over LAN
mode. An RMCP+ connection is made to the BMC, the
terminal is set to raw mode, and user input is sent to
the serial console on the remote server. On exit, the SOL
payload mode is deactivated and the terminal is reset to
its original settings.

Special escape sequences are provided to control the SOL
session:

~. Terminate connection

~^Z Suspend ipmitool

~^X Suspend ipmitool, but don't restore tty
on restart

~B Send break

~~ Send the escape character by typing it
twice

~? Print the supported escape sequences

Note that escapes are only recognized immediately after
newline.

kontronoem

OEM commands specific to Kontron devices.

setsn

Set FRU serial number.

setmfgdate

Set FRU manufacturing date.

nextboot <boot device>

Select the next boot order on the Kontron CP6012.

lan

These commands will allow you to configure IPMI LAN channels
with network information so they can be used with the ipmitool
lan and lanplus interfaces. NOTE: To determine on which channel
the LAN interface is located, issue the `channel info number'
command until you come across a valid 802.3 LAN channel. For
example:

> ipmitool -I open channel info 1
Channel 0x1 info:
Channel Medium Type : 802.3 LAN
Channel Protocol Type : IPMB-1.0
Session Support : session-based
Active Session Count : 8
Protocol Vendor ID : 7154

print [<channel>]

Print the current configuration for the given
channel. The default will print information on the first
found LAN channel.

set <channel number> <command> <parameter>

Set the given command and parameter on the specified
channel. Valid command/parameter options are:

ipaddr <x.x.x.x>

Set the IP address for this channel.

netmask <x.x.x.x>

Set the netmask for this channel.

macaddr <xx:xx:xx:xx:xx:xx>

Set the MAC address for this channel.

defgw ipaddr <x.x.x.x>

Set the default gateway IP address.

defgw macaddr <xx:xx:xx:xx:xx:xx>

Set the default gateway MAC address.

bakgw ipaddr <x.x.x.x>

Set the backup gateway IP address.

bakgw macaddr <xx:xx:xx:xx:xx:xx>

Set the backup gateway MAC address.

password <pass>

Set the null user password.

snmp <community string>

Set the SNMP community string.

user

Enable user access mode for userid 1 (issue the
`user' command to display information about
userids for a given channel).

access <on|off>

Set LAN channel access mode.

alert <on|off>

Enable or disable PEF alerting for this channel.

ipsrc <source>

Set the IP address source:
none unspecified
static manually configured static IP address
dhcp address obtained by BMC running DHCP
bios address loaded by BIOS or system software

arp respond <on|off>

Set BMC generated ARP responses.

arp generate <on|off>

Set BMC generated gratuitous ARPs.

arp interval <seconds>

Set BMC generated gratuitous ARP interval.

vlan id <off|id>

Disable VLAN operation or enable VLAN and set the
ID.
ID: value of the virtual lan identifier between 1
and 4094 inclusive.

vlan priority <priority>

Set the priority associated with VLAN frames.
ID: priority of the virtual lan frames between 0
and 7 inclusive.

auth <level,...> <type,...>

Set the valid authtypes for a given auth
level.
Levels: callback, user, operator, admin
Types: none, md2, md5, password, oem

cipher_privs <privlist>

Correlates cipher suite numbers with the maximum
privilege level that is allowed to use it. In
this way, cipher suites can restricted to users
with a given privilege level, so that, for
example, administrators are required to use a
stronger cipher suite than normal users.

The format of privlist is as follows. Each
character represents a privilege level and the
character position identifies the cipher suite
number. For example, the first character
represents cipher suite 0, the second represents
cipher suite 1, and so on. privlist must be 15
characters in length.

Characters used in privlist and their associated
privilege levels are:

X Cipher Suite Unused
c CALLBACK
u USER
o OPERATOR
a ADMIN
O OEM

So, to set the maximum privilege for cipher suite
0 to USER and suite 1 to ADMIN, issue the
following command:

> ipmitool -I interface lan set channel
cipher_privs uaXXXXXXXXXXXXX

bad_pass_thresh <thresh_num> <1|0> <reset_interval>
<lockout_interval>

Sets the Bad Password Threshold.

<thresh_num> If non-zero, this value determines
the number of sequential bad passwords that will
be allowed to be entered for the identified user
before the user is automatically disabled from
access on the channel.

<1|0> 1 = generate a Session Audit sensor "Invalid
password disable" event message. 0 = do not
generate an event message when the user is
disabled.

<reset_interval> Attempt Count Reset Interval. The
interval, in tens of seconds, for which the
accumulated count of bad password attempts is
retained before being automatically reset to zero.

<lockout_interval> User Lockout Interval. The
interval, in tens of seconds, that the user will
remain disabled after being disabled because the
Bad Password Threshold number was reached.

alert print [<channel>] [<alert destination>]

Print alert information for the specified channel and
destination. The default will print all alerts for all
alert destinations on the first found LAN channel.

alert set <channel number> <alert destination> <command>
<parameter>

Set an alert on the given LAN channel and destination.
Alert Destinations are listed via the 'lan alert print'
command. Valid command/parameter options are:

ipaddr <x.x.x.x>

Set alert IP address.

macaddr <xx:xx:xx:xx:xx:xx>

Set alert MAC address.

gateway <default | backup>

Set the channel gateway to use for alerts.

ack <on | off>

Set Alert Acknowledge on or off.

type <pet | oem1 | oem2>

Set the destination type as PET or OEM.

time <seconds>

Set ack timeout or unack retry interval.

retry <number>

Set the number of alert retries.

stats get [<channel number>]

Retrieve information about the IP connections on the
specified channel. The default will retrieve statistics
on the first found LAN channel.

stats clear [<channel number>]

Clear all IP/UDP/RMCP Statistics to 0 on the specified
channel. The default will clear statistics on the first
found LAN channel.

mc | bmc

reset <warm|cold>

Instructs the BMC to perform a warm or cold reset.

guid

Display the Management Controller Globally Unique
IDentifier.

info

Displays information about the BMC hardware, including
device revision, firmware revision, IPMI version
supported, manufacturer ID, and information on additional
device support.

watchdog

These commands allow a user to view and change the
current state of the watchdog timer.

get

Show current Watchdog Timer settings and countdown
state.

reset

Reset the Watchdog Timer to its most recent state
and restart the countdown timer.

off

Turn off a currently running Watchdog countdown
timer.

selftest

Check on the basic health of the BMC by executing the Get
Self Test results command and report the results.

getenables

Displays a list of the currently enabled options for the
BMC.

setenables <option>=[on|off]

Enables or disables the given option. This command is
only supported over the system interface according to the
IPMI specification. Currently supported values for
option include:

recv_msg_intr

Receive Message Queue Interrupt

event_msg_intr

Event Message Buffer Full Interrupt

event_msg

Event Message Buffer

system_event_log

System Event Logging

oem0

OEM-Defined option #0

oem1

OEM-Defined option #1

oem2

OEM-Defined option #2

getsysinfo <argument>
Retrieves system info from bmc for given argument.
See setsysinfo for argument definitions

setsysinfo <argument> <string>
Stores system info string to bmc for given argument

Possible arguments are:

primary_os_name Primary Operating System Name

os_name Operating System Name

system_name System Name of Server

delloem_os_version Running version of operating
system

delloem_URL URL of BMC Webserver

chassis

status

Displays information regarding the high-level
status of the system chassis and main power
subsystem.

poh

This command will return the Power-On Hours
counter.

identify <interval>

Control the front panel identify light. Default
interval is 15 seconds. Use 0 to turn off. Use
"force" to turn on indefinitely.

restart_cause

Query the chassis for the cause of the last system
restart.

selftest

Check on the basic health of the BMC by executing
the Get Self Test results command and report the
results.

policy

Set the chassis power policy in the event power
failure.

list

Return supported policies.

always-on

Turn on when power is restored.

Returned to previous state when power
is restored.

always-off

Stay off after power is restored.

power

Performs a chassis control command to view and
change the power state.

status

Show current chassis power status.

Power up chassis.

off

Power down chassis into soft off (S4/S5
state). WARNING: This command does not
initiate a clean shutdown of the operating
system prior to powering down the system.

cycle

Provides a power off interval of at least 1
second. No action should occur if chassis
power is in S4/S5 state, but it is
recommended to check power state first and
only issue a power cycle command if the
system power is on or in lower sleep state
than S4/S5.

reset

This command will perform a hard reset.

diag

Pulse a diagnostic interrupt (NMI) directly
to the processor(s).

soft

Initiate a soft-shutdown of OS via ACPI.
This can be done in a number of ways,
commonly by simulating an overtemperture or
by simulating a power button press. It is
necessary for there to be Operating System
support for ACPI and some sort of daemon
watching for events for this soft power to
work.

bootdev <device> [<clear-cmos=yes|no>]
[<options=help,...>]

Request the system to boot from an alternate boot
device on next reboot. The clear-cmos option, if
supplied, will instruct the BIOS to clear its CMOS
on the next reboot. Various options may be used
to modify the boot device settings. Run "bootdev
none options=help" for a list of available boot
device modifiers/options.

Currently supported values for <device> are:

none

Do not change boot device

pxe

Force PXE boot

disk

Force boot from BIOS default boot device

safe

Force boot from BIOS default boot device,
request Safe Mode

diag

Force boot from diagnostic partition

cdrom

Force boot from CD/DVD

bios

Force boot into BIOS setup

floppy

Force boot from Floppy/primary removable
media

bootparam

Get or set various system boot option parameters.

get <param #>

Get boot parameter. Currently supported
values for <param #> are:

0 - Set In Progress

1 - Service Partition Selector

2 - Service Partition Scan

3 - BMC Boot Flag Valid Bit Clearing

4 - Boot Info Acknowledge

5 - Boot Flags

6 - Boot Initiator Info

7 - Boot Initiator Mailbox

set <device> [<options=help,...>]

Set boot device parameter used for next
boot. Various options may be used to
change when the the next boot device is
cleared. Run "options=help" for a list of
available bootparam set device options.

Currently supported bootparam device
settings are:

force_pxe

Force PXE boot

force_disk

Force boot from default hard-drive

force_safe

Force boot from default hard-drive,
request Safe Mode

force_diag

Force boot from diagnostic partition

force_cdrom

Force boot from CD/DVD

force_bios

Force boot into BIOS setup

Currently supported bootparam options
settings are associated with BMC Boot Valid
Bit Clearing and are as follows: Any
option can be prefixed with "no-" to invert
the sense of the operation.

PEF

Clear valid bit on reset/power cycle
caused by PEF

timeout

Automatically clear boot flag valid
bit if Chassis Control command is
not received within 60 seconds.

watchdog

Clear valid bit on reset/power cycle
caused by watchdog timeout

reset

Clear valid bit on push button reset
/ soft-reset

power

Clear valid bit on power up via
power push button or wake event

alert

clear dest <dest>

Clear the Node Manager Alert lan destination.

get
Get the Node Manager Alert settings.

set chan <chan> dest <dest> string <string>

Set the Node Manager alert channel, lan
destination, and alert string number.

capability

Obtain the Node Manager power control capabilities and
ranges.

control

enable|disable

global

Enable/disable all policies for all
domains.

per_domain <platform|CPU|Memory>

Enable/disable all policies of the
specified domain.

per_policy <0-7>

Enable/disable the policy for the specified
domain/policy combination.

discover

Discover Node Manager presence as well as the Node
Manager version, revision, and patch number.

policy

add

Add a new power policy, or overwrite an
existing policy. The correction parameter
is the agressiveness of frequency limiting,
default is auto. The trig_lim is the
correction time limit and must be at least
6000 and not greater than 65535. The stats
setting is the averaging period in seconds
and ranges from 1-65535. If domain is not
supplied a default of platform is used.

Add a new inlet temp policy, or overwrite
an existing policy. The correction
parameter is the agressiveness of frequency
limiting, default is auto. The trig_lim is
the correction time limit and must be at
least 6000 and not greater than 65535. The
stats setting is the averaging period in
seconds and ranges from 1-65535. If domain
is not supplied a default of platform is
used.

get policy_id <0-7>

Get a previously stored policy.

limiting

Report policy number if any policy is limiting
power.

remove policy_id <0-7> [domain <platform|CPU|Memory>]

Remove a policy. If domain is not supplied a
default of platform is used.

power min <minimum> max <maximum> [domain <platform|CPU|Memory>]

Configure Node Manager power minimum and maximum power
draw limits. The min and max values must be in the range
of 0-65535. If domain is not supplied a default of
platform is used.

reset

comm policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager communication statistics. If
domain is not supplied a default of platform is
used.

global

Reset Node Manager global statistics.

memory policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager memory throttling statistics.
If domain is not supplied a default of platform is
used.

per_policy policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager per policy statistics. If
domain is not supplied a default of platform is
used.

requests policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager unhandled requests statistics.
If domain is not supplied a default of platform is
used.

response policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager response time statistics. If
domain is not supplied a default of platform is
used.

throttling policy_id <0-7> [domain <platform|CPU|Memory>]

Reset Node Manager throttling statistics. If
domain is not supplied a default of platform is
used.

statistics

comm_fail

Report Node Manager communication failure
statistics.

cpu_throttling

Report Node Manager cpu throttling statistics.

mem_throttling

Report Node Manager memory throttling statistics.

policy_power policy_id <0-7> [domain
<platform|CPU|Memory>]

Report Node Manager per policy power statistics
(policy must be a power limit type policy). If
domain is not supplied a default of platform is
used.

policy_temps policy_id <0-7> [domain
<platform|CPU|Memory>]

Report Node Manager per policy temp statistics
(policy must be an inlet temp limit policy). If
domain is not supplied a default of platform is
used.

policy_throt policy_id <0-7> [domain
<platform|CPU|Memory>]

Report Node Manager per policy throttling
statistics. If domain is not supplied a default
of platform is used.

requests

Report Node Manager unhandled requests statistics.

response

Report Node Manager response time statistics.

suspend

get policy_id <0-7> [domain <platform|CPU|Memory>]

Get Node Manager policy suspend periods. If
domain is not supplied a default of platform is
used.

set policy_id <0-7> [domain <platform|CPU|Memory>]
<start> <stop> <repeat>

Set Node Manager policy suspend periods. If
domain is not supplied a default of platform is
used. The <start> and <stop> values must be in
the range of 0-239, which is the number of minutes
past midnight divided by 6. The <repeat> value is
the daily recurrence pattern. Bit 0 is repeat
every Monday, bit 1 is repeat every Tuesday, on
through bit 6 for Sunday.

threshold

get policy_id <0-7> [domain <platform|CPU|Memory>]

Get Node Manager policy Alert Threshold settings.
If domain is not supplied a default of platform is
used.

set policy_id <0-7> [domain <platform|CPU|Memory>]
thresh_array

Set Node Manager policy Alert Threshold values.
If domain is not supplied a default of platform is
used. The thresh_array is 1, 2, or 3 integers
that set three alert threshold settings. The
setting type is a power or temperature value which
must match the type of policy.

pef

info

This command will query the BMC and print information
about the PEF supported features.

status

This command prints the current PEF status (the last SEL
entry processed by the BMC, etc).

policy

This command lists the PEF policy table entries. Each
policy entry describes an alert destination. A policy
set is a collection of table entries. PEF alert actions
reference policy sets.

list

This command lists the PEF table entries. Each PEF entry
relates a sensor event to an action. When PEF is active,
each platform event causes the BMC to scan this table for
entries matching the event, and possible actions to be
taken. Actions are performed in priority order (higher
criticality first).

picmg <properties>

Run a PICMG/ATA extended command. Get PICMG properties may be
used to obtain and print Extension major version information,
PICMG identifier, FRU Device ID and Max FRU Device ID.

addrinfo

Get address information. This command may return
information on the Hardware address, IPMB-0 Address, FRU
ID, Site/Entity ID, and Site/Entity Type.

frucontrol <fru id> <options>

Set various control options:

0x00 - Cold Reset

0x01 - Warm Reset

0x02 - Graceful Reboot

0x03 - Issue Diagnostic Interrupt

0x04 - Quiesce [AMC only]

0x05-0xFF - Cold Reset

activate <fru id>

Activate the specified FRU.

deactivate <fru id>

Deactivate the specified FRU.

policy get <fru id>

Get FRU activation policy.

policy set <fru id> <lockmask> <lock>

Set FRU activation policy. lockmask is 1 or 0 to
indicate action on the deactivation or activation locked
bit respectively. lock is 1 or 0 to set/clear locked
bit.

portstate set|getall|getgranted|getdenied <parameters>
Get or set various port states. See usage for parameter
details.

power <chassis power command>

Shortcut to the chassis power commands. See the chassis power
commands for usage information.

raw <netfn> <cmd> [<data>]

This will allow you to execute raw IPMI commands. For example
to query the POH counter with a raw command:

> ipmitool -v raw 0x0 0xf
RAW REQ (netfn=0x0 cmd=0xf data_len=0)
RAW RSP (5 bytes)
3c 72 0c 00 00

Note that the OpenIPMI driver provided by the Linux kernel will
reject the Get Message, Send Message and Read Event Message
Buffer commands because it handles the message sequencing
internally.

sdr

get <id> ... [<id>]

Prints information for sensor data records specified by
sensor id.

info

This command will query the BMC for Sensor Data Record
(SDR) Repository information.

type [<sensor type>]

This command will display all records from the SDR
Repository of a specific type. Run with type list (or
simply with no type) to see the list of available types.
For example to query for all Temperature sensors:

> ipmitool sdr type Temperature
Baseboard Temp | 30h | ok | 7.1 | 28 degrees C
FntPnl Amb Temp | 32h | ok | 12.1 | 24 degrees C
Processor1 Temp | 98h | ok | 3.1 | 57 degrees C
Processor2 Temp | 99h | ok | 3.2 | 53 degrees C

This command will read the Sensor Data Records (SDR) and
extract sensor information of a given type, then query
each sensor and print its name, reading, and status. If
invoked as elist then it will also print sensor number,
entity id and instance, and asserted discrete states.

The default output will only display full and compact
sensor types, to see all sensors use the all type with
this command.

Valid types are:

all

All SDR records (Sensor and Locator)

full

Full Sensor Record

compact

Compact Sensor Record

event

Event-Only Sensor Record

mcloc

Management Controller Locator Record

fru

FRU Locator Record

generic

Generic SDR records

entity <id>[.<instance>]

Displays all sensors associated with an entity. Get a
list of valid entity ids on the target system by issuing
the sdr elist command. A list of all entity ids can be
found in the IPMI specifications.

dump <file>

Dumps raw SDR data to a file. This data file can then be
used as a local SDR cache of the remote managed system
with the -S <file> option on the ipmitool command line.
This can greatly improve performance over system
interface or remote LAN.

fill sensors

Create the SDR Repository for the current configuration.
Will perform a 'Clear SDR Repository' command so be
careful.

fill file <filename>

Fill the SDR Repository using records stored in a binary
data file. Will perform a 'Clear SDR Repository' command
so be careful.

sel

NOTE: System Event Log (SEL) entry-times are displayed as
`Pre-Init Time-stamp' if the SEL clock needs to be set. Ensure
that the SEL clock is accurate by invoking the sel time get and
sel time set <time string> commands.

info

This command will query the BMC for information about the
System Event Log (SEL) and its contents.

clear

This command will clear the contents of the SEL. It
cannot be undone so be careful.

list | elist

When this command is invoked without arguments, the
entire contents of the System Event Log are displayed.
If invoked as elist (extended list) it will also use the
Sensor Data Record entries to display the sensor ID for
the sensor that caused each event. Note this can take a
long time over the system interface.

<count> | first <count>

Displays the first count (least-recent) entries in
the SEL. If count is zero, all entries are
displayed.

last <count>

Displays the last count (most-recent) entries in
the SEL. If count is zero, all entries are
displayed.

delete <SEL Record ID> ... <SEL Record ID>

Delete one or more SEL event records.

add <filename ID>

Read event entries from a file and add them to the SEL.
New SEL entries area added onto the SEL after the last
record in the SEL. Record added is of type 2 and is
automatically timestamped.

get <SEL Record ID>

Print information on the specified SEL Record entry.

save <file>

Save SEL records to a text file that can be fed back into
the event file ipmitool command. This can be useful for
testing Event generation by building an appropriate
Platform Event Message file based on existing events.
Please see the available help for the 'event file ...'
command for a description of the format of this file.

writeraw <file>

Save SEL records to a file in raw, binary format. This
file can be fed back to the sel readraw ipmitool command
for viewing.

readraw <file>

Read and display SEL records from a binary file. Such a
file can be created using the sel writeraw ipmitool
command.

time

get
Displays the SEL clock's current time.

set <time string>

Sets the SEL clock. Future SEL entries will use
the time set by this command. <time string> is of
the form "MM/DD/YYYY HH:MM:SS". Note that hours
are in 24-hour form. It is recommended that the
SEL be cleared before setting the time.

sensor

list

Lists sensors and thresholds in a wide table format.

get <id> ... [<id>]

Prints information for sensors specified by name.

thresh <id> <threshold> <setting>

This allows you to set a particular sensor threshold
value. The sensor is specified by name.

Valid thresholds are:
unr Upper Non-Recoverable
ucr Upper Critical
unc Upper Non-Critical
lnc Lower Non-Critical
lcr Lower Critical
lnr Lower Non-Recoverable

thresh <id> lower <lnr> <lcr> <lnc>

This allows you to set all lower thresholds for a sensor
at the same time. The sensor is specified by name and
the thresholds are listed in order of Lower
Non-Recoverable, Lower Critical, and Lower Non-Critical.

thresh <id> upper <unc> <ucr> <unr>

This allows you to set all upper thresholds for a sensor
at the same time. The sensor is specified by name and
the thresholds are listed in order of Upper Non-Critical,
Upper Critical, and Upper Non-Recoverable.

session

info <active|all|id 0xnnnnnnnn|handle 0xnn>

Get information about the specified session(s). You may
identify sessions by their id, by their handle number, by
their active status, or by using the keyword `all' to
specify all sessions.

set

hostname <host>

Session hostname.

username <user>

Session username.

password <pass>

Session password.

privlvl <level>

Session privilege level force.

authtype <type>

Authentication type force.

localaddr <addr>

Local IPMB address.

targetaddr <addr>

Remote target IPMB address.

port <port>

Remote RMCP port.

csv [level]

Enable output in comma separated format. Affects
following commands: user, channel, isol, sunoem, sol,
sensor, sdr, sel, session.

verbose [verbose]

Verbosity level.

shell
This command will launch an interactive shell which you can use
to send multiple ipmitool commands to a BMC and see the
responses. This can be useful instead of running the full
ipmitool command each time. Some commands will make use of a
Sensor Data Record cache and you will see marked improvement in
speed if these commands are able to reuse the same cache in a
shell session. LAN sessions will send a periodic keepalive
command to keep the IPMI session from timing out.

sol

info [<channel number>]

Retrieve information about the Serial-Over-LAN
configuration on the specified channel. If no channel is
given, it will display SOL configuration data for the
currently used channel.

payload <enable | disable | status> <channel number> <userid>

Enable, disable or show status of SOL payload for the
user on the specified channel.

set <parameter> <value> [<channel>]

Configure parameters for Serial Over Lan. If no channel
is given, it will display SOL configuration data for the
currently used channel. Configuration parameter updates
are automatically guarded with the updates to the
set-in-progress parameter.

Valid parameters and values are:

set-in-progress
set-complete set-in-progress commit-write

enabled
true false

force-encryption
true false

force-authentication
true false

privilege-level
user operator admin oem

character-accumulate-level
Decimal number given in 5 milliseconds increments

character-send-threshold
Decimal number

retry-count
Decimal number. 0 indicates no retries after
packet is transmitted.

retry-interval
Decimal number in 10 millisecond increments. 0
indicates that retries should be sent back to
back.

non-volatile-bit-rate
serial, 19.2, 38.4, 57.6, 115.2. Setting this
value to serial indicates that the BMC should use
the setting used by the IPMI over serial channel.

volatile-bit-rate
serial, 19.2, 38.4, 57.6, 115.2. Setting this
value to serial indicates that the BMC should use
the setting used by the IPMI over serial channel.

activate [usesolkeepalive | nokeepalive] [instance=<number>]

Causes ipmitool to enter Serial Over LAN mode, and is
only available when using the lanplus interface. An
RMCP+ connection is made to the BMC, the terminal is set
to raw mode, and user input is sent to the serial console
on the remote server. On exit, the the SOL payload mode
is deactivated and the terminal is reset to its original
settings.

If the instance is given, it will activate using the
given instance number. The default is 1.

Special escape sequences are provided to control the SOL
session:

~. Terminate connection

~^Z Suspend ipmitool

~^X Suspend ipmitool, but don't restore tty on
restart

~B Send break

~~ Send the escape character by typing it twice

~? Print the supported escape sequences

Note that escapes are only recognized immediately after
newline.

deactivate [instance=<number>]

Deactivates Serial Over LAN mode on the BMC. Exiting
Serial Over LAN mode should automatically cause this
command to be sent to the BMC, but in the case of an
unintentional exit from SOL mode, this command may be
necessary to reset the state of the BMC.

If the instance is given, it will deactivate the given
instance number. The default is 1.

spd <i2cbus> <i2caddr> [<channel>] [<axread>]

This command may be used to read SPD (Serial Presence Detect)
data using the I2C Master Write-Read IPMI command.

sunoem

cli [<command string> ...]

Execute the service processor command line interface
commands. Without any command string, an interactive
session is started in the service processor command line
environment. If a command string is specified, the
command string is executed on the service processor and
the connection is closed.

led

These commands provide a way to get and set the status of
LEDs on a Sun Microsystems server. Use 'sdr list
generic' to get a list of devices that are controllable
LEDs. The ledtype parameter is optional and not
necessary to provide on the command line unless it is
required by hardware.

get <sensorid> [<ledtype>]

Get status of a particular LED described by a
Generic Device Locator record in the SDR. A
sensorid of all will get the status of all
available LEDS.

set <sensorid> <ledmode> [<ledtype>]

Set status of a particular LED described by a
Generic Device Locator record in the SDR. A
sensorid of all will set the status of all
available LEDS to the specified ledmode and
ledtype.

LED Mode is required for set operations:
OFF Off
ON Steady On
STANDBY 100ms on 2900ms off blink rate
SLOW 1HZ blink rate
FAST 4HZ blink rate

LED Type is optional:
OK2RM Ok to Remove
SERVICE Service Required
ACT Activity
LOCATE Locate

nacname <ipmi name>

Return the full NAC name of a target identified by ipmi
name.

ping <count> [<q>]

Send and receive count packets. Each packet is 64 bytes.

q - Quiet. Displays output only at the start and end of
the process.

getval <property name>

Returns value of specified ILOM property.

setval <property name> <property value> [<timeout>]

Sets value of ILOM property. If timeout is not
specified, the default value is 5 seconds. NOTE: setval
must be executed locally on host!

sshkey

set <userid> <keyfile>

This command will allow you to specify an SSH key
to use for a particular user on the Service
Processor. This key will be used for CLI logins to
the SP and not for IPMI sessions. View available
users and their userids with the 'user list'
command.

del <userid>

This command will delete the SSH key for a
specified userid.

version

Display the version of ILOM firmware.

getfile <file identifier> <destination file name>

This command will return various files from service
processor and store them in specified destination file.
Note that some files may not be present or be supported
by your SP.

File identifiers:
SSH_PUBKEYS
DIAG_PASSED
DIAG_FAILED
DIAG_END_TIME
DIAG_INVENTORY
DIAG_TEST_LOG
DIAG_START_TIME
DIAG_UEFI_LOG
DIAG_TEST_LOG
DIAG_LAST_LOG
DIAG_LAST_CMD

getbehavior <feature identifier>

This command will test if various ILOM features are
enabled.

Feature identifiers:
SUPPORTS_SIGNED_PACKAGES
REQUIRES_SIGNED_PACKAGES

tsol

This command allows Serial-over-LAN sessions to be established
with Tyan IPMIv1.5 SMDC such as the M3289 or M3290. The default
command run with no arguments will establish default SOL session
back to local IP address. Optional arguments may be supplied in
any order.

Send receiver IP address to SMDC which it will use to
send serial traffic to. By default this detects the
local IP address and establishes two-way session. Format
of ipaddr is XX.XX.XX.XX

port=NUM

Configure UDP port to receive serial traffic on. By
default this is 6230.

ro|rw

Confiure SOL session as read-only or read-write.
Sessions are read-write by default.

user

summary

Displays a summary of userid information, including
maximum number of userids, the number of enabled users,
and the number of fixed names defined.

list

Displays a list of user information for all defined
userids.

set

name <userid> <username>

Sets the username associated with the given
userid.

password <userid> [<password>]

Sets the password for the given userid. If no
password is given, the password is cleared (set to
the NULL password). Be careful when removing
passwords from administrator-level accounts.

disable <userid>

Disables access to the BMC by the given userid.

enable <userid>

Enables access to the BMC by the given userid.

priv <userid> <privilege level> [<channel number>]

Set user privilege level on the specified channel. If
the channel is not specified, the current channel will be
used.

test <userid> <16|20> [<password>]

Determine whether a password has been stored as 16 or 20
bytes.

OPEN INTERFACE
The ipmitool open interface utilizes the OpenIPMI kernel device driver.
This driver is present in all modern 2.4 and all 2.6 kernels and it
should be present in recent Linux distribution kernels. There are also
IPMI driver kernel patches for different kernel versions available from
the OpenIPMI homepage.

The required kernel modules is different for 2.4 and 2.6 kernels. The
following kernel modules must be loaded on a 2.4-based kernel in order
for ipmitool to work:

ipmi_msghandler
Incoming and outgoing message handler for IPMI interfaces.

ipmi_kcs_drv
An IPMI Keyboard Controller Style (KCS) interface driver for the
message handler.

ipmi_devintf
Linux character device interface for the message handler.

The following kernel modules must be loaded on a 2.6-based kernel in
order for ipmitool to work:

ipmi_msghandler
Incoming and outgoing message handler for IPMI interfaces.

ipmi_si
An IPMI system interface driver for the message handler. This
module supports various IPMI system interfaces such as KCS, BT,
SMIC, and even SMBus in 2.6 kernels.

ipmi_devintf
Linux character device interface for the message handler.

Once the required modules are loaded there will be a dynamic character
device entry that must exist at /dev/ipmi0. For systems that use devfs
or udev this will appear at /dev/ipmi/0.

To create the device node first determine what dynamic major number it
was assigned by the kernel by looking in /proc/devices and checking for
the ipmidev entry. Usually if this is the first dynamic device it will
be major number 254 and the minor number for the first system interface
is 0 so you would create the device entry with:

mknod /dev/ipmi0 c 254 0

ipmitool includes some sample initialization scripts that can perform
this task automatically at start-up.

In order to have ipmitool use the OpenIPMI device interface you can
specify it on the command line:

ipmitool -I open <command>

BMC INTERFACE
The ipmitool bmc interface utilizes the bmc device driver as provided
by Solaris 10 and higher. In order to force ipmitool to make use of
this interface you can specify it on the command line:

ipmitool -I bmc <command>

The following files are associated with the bmc driver:

/platform/i86pc/kernel/drv/bmc
32-bit ELF kernel module for the bmc driver.

/platform/i86pc/kernel/drv/amd64/bmc
64-bit ELF kernel module for the bmc driver.

/dev/bmc
Character device node used to communicate with the bmc driver.

LIPMI INTERFACE
The ipmitool lipmi interface uses the Solaris 9 IPMI kernel device
driver. It has been superceeded by the bmc interface on Solaris 10.
You can tell ipmitool to use this interface by specifying it on the
command line.

ipmitool -I lipmi <expression>

LAN INTERFACE
The ipmitool lan interface communicates with the BMC over an Ethernet
LAN connection using UDP under IPv4. UDP datagrams are formatted to
contain IPMI request/response messages with a IPMI session headers and
RMCP headers.

IPMI-over-LAN uses version 1 of the Remote Management Control Protocol
(RMCP) to support pre-OS and OS-absent management. RMCP is a
request-response protocol delivered using UDP datagrams to port 623.

The LAN interface is an authentication multi-session connection;
messages delivered to the BMC can (and should) be authenticated with a
challenge/response protocol with either straight password/key or MD5
message-digest algorithm. ipmitool will attempt to connect with
administrator privilege level as this is required to perform chassis
power functions.

You can tell ipmitool to use the lan interface with the -I lan option:

ipmitool -I lan -H <hostname> [-U <username>] [-P <password>] <command>

A hostname must be given on the command line in order to use the lan
interface with ipmitool. The password field is optional; if you do not
provide a password on the command line, ipmitool will attempt to
connect without authentication. If you specify a password it will use
MD5 authentication if supported by the BMC and straight password/key
otherwise, unless overridden with a command line option.

LANPLUS INTERFACE
Like the lan interface, the lanplus interface communicates with the BMC
over an Ethernet LAN connection using UDP under IPv4. The difference
is that the lanplus interface uses the RMCP+ protocol as described in
the IPMI v2.0 specification. RMCP+ allows for improved authentication
and data integrity checks, as well as encryption and the ability to
carry multiple types of payloads. Generic Serial Over LAN support
requires RMCP+, so the ipmitool sol activate command requires the use
of the lanplus interface.

RMCP+ session establishment uses a symmetric challenge-response
protocol called RAKP (Remote Authenticated Key-Exchange Protocol) which
allows the negotiation of many options. ipmitool does not yet allow
the user to specify the value of every option, defaulting to the most
obvious settings marked as required in the v2.0 specification.
Authentication and integrity HMACS are produced with SHA1, and
encryption is performed with AES-CBC-128. Role-level logins are not
yet supported.

ipmitool must be linked with the OpenSSL library in order to perform
the encryption functions and support the lanplus interface. If the
required packages are not found it will not be compiled in and
supported.

You can tell ipmitool to use the lanplus interface with the -I lanplus
option:

ipmitool -I lanplus -H <hostname> [-U <username>] [-P <password>]
<command>

A hostname must be given on the command line in order to use the lan
interface with ipmitool. With the exception of the -A and -C options
the rest of the command line options are identical to those available
for the lan interface.

The -C option allows you specify the authentication, integrity, and
encryption algorithms to use for for lanplus session based on the
cipher suite ID found in the IPMIv2.0 specification in table 22-19.
The default cipher suite is 3 which specifies RAKP-HMAC-SHA1
authentication, HMAC-SHA1-96 integrity, and AES-CBC-128 encryption
algorightms.

FREE INTERFACE
The ipmitool free interface utilizes the FreeIPMI libfreeipmi drivers.

You can tell ipmitool to use the FreeIPMI interface with the -I option:

ipmitool -I free <command>

IMB INTERFACE
The ipmitool imb interface supports the Intel IMB (Intel Inter-module
Bus) Interface through the /dev/imb device.

You can tell ipmitool to use the IMB interface with the -I option:

ipmitool -I imb <command>

EXAMPLES
Example 1: Listing remote sensors

Example 2: Displaying status of a remote sensor

> ipmitool -I lan -H 1.2.3.4 -f passfile sensor get "Baseboard
1.25V"
Locating sensor record...
Sensor ID : Baseboard 1.25V (0x10)
Sensor Type (Analog) : Voltage
Sensor Reading : 1.245 (+/- 0.039) Volts
Status : ok
Lower Non-Recoverable : na
Lower Critical : 1.078
Lower Non-Critical : 1.107
Upper Non-Critical : 1.382
Upper Critical : 1.431
Upper Non-Recoverable : na

Example 3: Displaying the power status of a remote chassis

> ipmitool -I lan -H 1.2.3.4 -f passfile chassis power status
Chassis Power is on

Example 4: Controlling the power on a remote chassis

> ipmitool -I lan -H 1.2.3.4 -f passfile chassis power on
Chassis Power Control: Up/On

AUTHOR
Duncan Laurie <duncan@iceblink.org>

SEE ALSO
IPMItool Homepage
http://ipmitool.sourceforge.net

Intelligent Platform Management Interface Specification
http://www.intel.com/design/servers/ipmi

OpenIPMI Homepage
http://openipmi.sourceforge.net

FreeIPMI Homepage
http://www.gnu.org/software/freeipmi/

Duncan Laurie ipmitool(1)