DragonFly On-Line Manual Pages
PPPOE.CONF(5) DragonFly File Formats Manual PPPOE.CONF(5)
NAME
pppoe.conf - Configuration file used by pppoe-start(8), pppoe-stop(8),
pppoe-status(8) and pppoe-connect(8).
DESCRIPTION
/usr/local/etc/ppp/pppoe.conf is a shell script which contains
configuration information for Roaring Penguin's PPPoE scripts. Note
that pppoe.conf is used only by the various pppoe-* shell scripts, not
by pppoe itself.
pppoe.conf consists of a sequence of shell variable assignments. The
variables and their meanings are:
ETH The Ethernet interface connected to the DSL modem (for example,
eth0).
USER The PPPoE user-id (for example, b1xxnxnx@sympatico.ca).
SERVICENAME
If this is not blank, then it is passed with the -S option to
pppoe. It specifies a service name to ask for. Usually, you
should leave it blank.
ACNAME If this is not blank, then it is passed with the -C option to
pppoe. It specifies the name of the access concentrator to
connect to. Usually, you should leave it blank.
DEMAND If set to a number, the link is activated on demand and brought
down after after DEMAND seconds. If set to no, the link is kept
up all the time rather than being activated on demand.
DNSTYPE
One of NOCHANGE, SPECIFY or SERVER. If set to NOCHANGE, pppoe-
connect will not adjust the DNS setup in any way. If set to
SPECIFY, it will re-write /etc/resolv.conf with the values of
DNS1 and DNS2. If set to SERVER, it will supply the usepeerdns
option to pppd, and make a symlink from /etc/resolv.conf to
/usr/local/etc/ppp/resolv.conf.
DNS1, DNS2
IP addresses of DNS servers if you use DNSTYPE=SPECIFY.
NONROOT
If the line NONROOT=OK (exactly like that; no whitespace or
comments) appears in the configuration file, then pppoe-wrapper
will allow non-root users to bring the conneciton up or down.
The wrapper is installed only if you installed the rp-pppoe-gui
package.
USEPEERDNS
If set to "yes", then pppoe-connect will supply the usepeerdns
option to pppd, which causes it to obtain DNS server addresses
from the peer and create a new /etc/resolv.conf file.
Otherwise, pppoe-connect will not supply this option, and pppd
will not modify /etc/resolv.conf.
CONNECT_POLL
How often (in seconds) pppoe-start should check to see if a new
PPP interface has come up. If this is set to 0, the pppoe-start
simply initiates the PPP session, but does not wait to see if it
comes up successfully.
CONNECT_TIMEOUT
How long (in seconds) pppoe-start should wait for a new PPP
interface to come up before concluding that pppoe-connect has
failed and killing the session.
PING A character which is echoed every CONNECT_POLL seconds while
pppoe-start is waiting for the PPP interface to come up.
FORCEPING
A character which is echoed every CONNECT_POLL seconds while
pppoe-start is waiting for the PPP interface to come up.
Similar to PING, but the character is echoed even if pppoe-
start's standard output is not a tty.
PIDFILE
A file in which to write the process-ID of the pppoe-connect
process (for example, /var/run/pppoe.pid). Two additional files
($PIDFILE.pppd and $PIDFILE.pppoe) hold the process-ID's of the
pppd and pppoe processes, respectively.
SYNCHRONOUS
An indication of whether or not to use synchronous PPP (yes or
no). Synchronous PPP is safe on Linux machines with the n_hdlc
line discipline. (If you have a file called "n_hdlc.o" in your
modules directory, you have the line discipline.) It is not
recommended on other machines or on Linux machines without the
n_hdlc line discipline due to some known and unsolveable race
conditions in a user-mode client.
CLAMPMSS
The value at which to "clamp" the advertised MSS for TCP
sessions. The default of 1412 should be fine.
LCP_INTERVAL
How often (in seconds) pppd sends out LCP echo-request packets.
LCP_FAILURE
How many unanswered LCP echo-requests must occur before pppd
concludes the link is dead.
PPPOE_TIMEOUT
If this many seconds elapse without any activity seen by pppoe,
then pppoe exits.
FIREWALL
One of NONE, STANDALONE or MASQUERADE. If NONE, then pppoe-
connect does not add any firewall rules. If STANDALONE, then it
clears existing firewall rules and sets up basic rules for a
standalone machine. If MASQUERADE, then it clears existing
firewall rules and sets up basic rules for an Internet gateway.
If you run services on your machine, these simple firewall
scripts are inadequate; you'll have to make your own firewall
rules and set FIREWALL to NONE.
PPPOE_EXTRA
Any extra arguments to pass to pppoe
PPPD_EXTRA
Any extra arguments to pass to pppd
LINUX_PLUGIN
If non-blank, the full path of the Linux kernel-mode PPPoE
plugin (typically /usr/local/etc/ppp/plugins/rp-pppoe.so.) This
forces pppoe-connect to use kernel-mode PPPoE on Linux 2.4.x
systems. This code is experimental and unsupported. Use of the
plugin causes pppoe-connect to ignore CLAMPMSS, PPPOE_EXTRA,
SYNCHRONOUS and PPPOE_TIMEOUT.
By using different configuration files with different PIDFILE settings,
you can manage multiple PPPoE connections. Just specify the
configuration file as an argument to pppoe-start and pppoe-stop.
SEE ALSO
pppoe(8), pppoe-connect(8), pppoe-start(8), pppoe-stop(8), pppd(8),
pppoe-setup(8), pppoe-wrapper(8)
4th Berkeley Distribution 21 February 2000 PPPOE.CONF(5)