DragonFly On-Line Manual Pages

RM(1)                  DragonFly General Commands Manual                 RM(1)

NAME
     rm, unlink -- remove directory entries

SYNOPSIS
     rm [-dfiIPRrvWx] file ...
     unlink file

DESCRIPTION
     The rm utility attempts to remove the non-directory type files specified
     on the command line.  If the permissions of the file do not permit
     writing, and the standard input device is a terminal, the user is
     prompted (on the standard error output) for confirmation.

     The options are as follows:

     -d          Attempt to remove directories as well as other types of
                 files.

     -f          Attempt to remove the files without prompting for
                 confirmation, regardless of the file's permissions.  If the
                 file does not exist, do not display a diagnostic message or
                 modify the exit status to reflect an error.  The -f option
                 overrides any previous -i options.

     -i          Request confirmation before attempting to remove each file,
                 regardless of the file's permissions, or whether or not the
                 standard input device is a terminal.  The -i option overrides
                 any previous -f options.

     -I          Request confirmation once if more than three files are being
                 removed or if a directory is being recursively removed.  This
                 option only applies when the rm utility is run in the
                 foreground.  This is a far less intrusive option than -i yet
                 provides almost the same level of protection against
                 mistakes.

     -P          Overwrite regular files before deleting them.  Files are
                 overwritten three times, first with the byte pattern 0xff,
                 then 0x00, and then 0xff again, before they are deleted.

                 A file with a link count greater than one will neither be
                 overwritten nor removed, and a warning will be issued.

     -R          Attempt to remove the file hierarchy rooted in each file
                 argument.  The -R option implies the -d option.  If the -i
                 option is specified, the user is prompted for confirmation
                 before each directory's contents are processed (as well as
                 before the attempt is made to remove the directory).  If the
                 user does not respond affirmatively, the file hierarchy
                 rooted in that directory is skipped.

     -r          Equivalent to -R.

     -v          Be verbose when deleting files, showing them as they are
                 removed.

     -W          Attempt to undelete the named files.  Currently, this option
                 can only be used to recover files covered by whiteouts.

     -x          When removing a hierarchy, don't cross mount points.

     The rm utility removes symbolic links, not the files referenced by the
     links.

     It is an error to attempt to remove the files ``.'' or ``..''.

     When the utility is called as unlink, only one argument, which must not
     be a directory, may be supplied.  No options may be supplied in this
     simple mode of operation, which performs an unlink(2) operation on the
     passed argument.

     The rm utility exits 0 if all of the named files or file hierarchies were
     removed, or if the -f option was specified and all of the existing files
     or file hierarchies were removed.  If an error occurs, rm exits with a
     value >0.

     If rm receives a SIGINFO (see the status argument for stty(1)) signal,
     the current file or directory being removed will be written to standard
     error.

NOTE
     The rm command uses getopt(3) to parse its arguments, which allows it to
     accept the `--' option which will cause it to stop processing flag
     options at that point.  This will allow the removal of file names that
     begin with a dash (`-').  For example:
           rm -- -filename
     The same behavior can be obtained by using an absolute or relative path
     reference.  For example:
           rm /home/user/-filename
           rm ./-filename

COMPATIBILITY
     The rm utility differs from historical implementations in that the -f
     option only masks attempts to remove non-existent files instead of
     masking a large variety of errors.  The -v option is non-standard and its
     use in scripts is not recommended.

     Also, historical BSD implementations prompted on the standard output, not
     the standard error output.

SEE ALSO
     chflags(1), rmdir(1), undelete(2), unlink(2), fts(3), getopt(3),
     symlink(7)

STANDARDS
     The rm command conforms to IEEE Std 1003.2 (``POSIX.2'').

     The simplified unlink command conforms to Version 2 of the Single UNIX
     Specification (``SUSv2'').

HISTORY
     A rm command appeared in Version 1 AT&T UNIX.

BUGS
     The -P option assumes that the underlying file system is a fixed-block
     file system.  UFS(5) is a fixed-block file system, LFS is not.  In
     addition, only regular files are overwritten, other types of files are
     not.  Hardlinked regular files will not be overwritten or removed,
     possibly leading to unintended behavior.  It is arguable which is the
     MORE unintended behavior.

DragonFly 3.5                   April 15, 2013                   DragonFly 3.5