DragonFly On-Line Manual Pages
AXE(4) DragonFly Kernel Interfaces Manual AXE(4)
NAME
axe - ASIX Electronics AX88x7x/760 USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device ehci
device uhci
device ohci
device usb
device miibus
device uether
device axe
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
if_axe_load="YES"
DESCRIPTION
The axe driver provides support for USB Ethernet adapters based on the
ASIX Electronics AX88172, AX88178, AX88772, AX88772A, AX88772B and
AX88760 USB 2.0 chipsets.
The AX88172, AX88772, AX88772A, AX88772B and AX88760 contain a 10/100
Ethernet MAC with MII interface and are designed to work with both
Ethernet and HomePNA transceivers. The AX88178 has a 10/100/1000
Ethernet MAC with GMII/RGMII interface for interfacing with Gigabit
Ethernet PHY.
These devices will operate with both USB 1.x and USB 2.0 controllers,
however performance with 1.x controllers will be limited since the USB
1.x standard specifies a maximum transfer speed of 12Mbps. Users with
USB 1.x controllers should therefore not expect to actually achieve
100Mbps speeds with these devices.
All chipsets support a 64-bit multicast hash table, single perfect filter
entry for the station address, all-multicast mode and promiscuous mode.
Packets are received and transmitted over separate USB bulk transfer
endpoints.
The axe driver supports the following media types:
autoselect Enable autoselection of the media type and options. The
user can manually override the autoselected mode by
adding media options to rc.conf(5).
10baseT/UTP Set 10Mbps operation. The ifconfig(8) mediaopt option
can also be used to select either full-duplex or
half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The ifconfig(8)
mediaopt option can also be used to select either
full-duplex or half-duplex modes.
1000baseT Set 1000Mbps (Gigabit Ethernet) operation (AX88178
only). The ifconfig(8) mediaopt option can also be used
to select either full-duplex or half-duplex modes.
The axe driver supports the following media options:
full-duplex Force full duplex operation.
half-duplex Force half duplex operation.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The axe driver supports ASIX Electronics
AX88172/AX88178/AX88772/AX88772A/AX88772B/AX88760 based USB Ethernet
adapters including:
AX88172:
* AboCom UF200
* Acer Communications EP1427X2
* ASIX AX88172
* ATen UC210T
* Billionton SnapPort
* Billionton USB2AR
* Buffalo (Melco Inc.) LUA-U2-KTX
* Corega USB2_TX
* D-Link DUBE100
* Goodway GWUSB2E
* JVC MP_PRX1
* LinkSys USB200M
* Netgear FA120
* Sitecom LN-029
* System TALKS Inc. SGC-X2UL
AX88178:
* ASIX AX88178
* Belkin F5D5055
* Logitec LAN-GTJ/U2A
* Buffalo (Melco Inc.) LUA3-U2-AGT
* Planex Communications GU1000T
* Sitecom Europe LN-028
AX88772:
* ASIX AX88772
* Buffalo (Melco Inc.) LUA3-U2-ATX
* D-Link DUBE100B1
* Planex UE-200TX-G
* Planex UE-200TX-G2
AX88772A:
* ASIX AX88772A
* Cisco-Linksys USB200Mv2
AX88772B:
* ASIX AX88772B
* Lenovo USB 2.0 Ethernet
AX88760:
* ASIX AX88760
DIAGNOSTICS
axe%d: watchdog timeout A packet was queued for transmission and a
transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
axe%d: no memory for rx list The driver failed to allocate an mbuf for
the receiver ring.
SEE ALSO
altq(4), arp(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4),
rgephy(4), usb(4), vlan(4), ifconfig(8)
ASIX AX88x7x and AX88760 data sheets, http://www.asix.com.tw.
HISTORY
The axe device driver first appeared in FreeBSD 5.0.
AUTHORS
The axe driver was written by Bill Paul <wpaul@windriver.com>.
DragonFly 5.9-DEVELOPMENT May 27, 2021 DragonFly 5.9-DEVELOPMENT