DragonFly On-Line Manual Pages
nfcapd(1) nfcapd(1)
NAME
nfcapd - netflow capture daemon
SYNOPSIS
nfcapd [options]
DESCRIPTION
nfcapd is the netflow capture daemon of the nfdump tools. It reads
netflow data from the network and stores it into files. The output file
is automatically rotated and renamed every n minutes - typically 5 min
- according the timestamp YYYYMMddhhmm of the interval e.g.
nfcapd.201107110845 contains the data from July 11th 2011 08:45 onward.
Netflow version v1, v5, v7 and v9 and IPFIX are transparently
supported.
Extensions: nfcapd supports a large number of v9 tags. In order to
optimise disk space and performance, v9 tags are grouped into a number
of extensions which may or may not be stored into the data file.
Therefore the v9 templates configured on the exporter may be tuned
according the collector. Only those tags common to both are stored into
the data files.
Sampling: By default, the sampling rate is set to 1 (unsampled) or to
any given value specified by the -s cmd line option. If sampling
information is found in the netflow stream, it overwrites the default
value. Sampling is automatically recognised when announced in v9 option
templates (tags #34, #35 or #48, #49, #50 ) or in the unofficial v5
header hack. Note: Not all platforms (or IOS/JunOS versions) support
exporting sampling information in netflow data, even if sampling is
configured. The number of bytes/packets in each netflow record is
automatically multiplied by the sampling rate. The total number of
flows is not changed as this is not accurate enough. (Small flows
versus large flows) If the default sampling rate given by -s is
negative, this will hard overwrite any device specific announced
sampling rates.
NSEL/ASA Support: nfcapd can be compiled with NSEL/ASA support
included. See notes on NSEL/ASA
NEL (NAT Event logging): nfcapd can be compiled with CISCO NEL support
included. See notes on NEL.
OPTIONS
-p portnum
Specifies the port number to listen. Default port is 9995
-b bindhost
Specifies the hostname/IPv4/IPv6 address to bind for listening. This
can be an IP address or a hostname, resolving to an IP address
attached to an interface. Defaults to any available IPv4 interface,
if not specified.
-4 Forces nfcapd to listen on IPv4 addresses only. Can be used together
with -b if a hostname has an IPv4 and IPv6 address record.
-6 Forces nfcapd to listen on IPv6 addresses only. Can be used together
with -b if a hostname has an IPv4 and IPv6 address record. Depending
on the socket implementation -6 also accepts IPv4 data.
-j MulticastGroup
Join the specified IPv4 or IPv6 multicast group for listening.
-R host[/port}
Enable packet repeater. Send all incoming packets to another host
and port. host is either a valid IPv4/IPv6 address, or a valid
symbolic hostname, which resolves to a IPv6 or IPv4 address. port
may be ommited and defaults to port 9995. Note: Due to IPv4/IPv6
accepted addresses the port separator is '/'.
-I IdentString ( capital letter i )
Specifies an ident string, which describes the source e.g. the name
of the router. This string is put into the stat record to identify
the source. Default is 'none'. This is for compatibility with nfdump
1.5.x and used to specify a single netflow source. See -n
-l base_directory ( letter ell )
Specifies the base directory to store the output files. If a sub
hierarchy is specified with -S the final directory is concatenated
to base_directory/sub_hierarchy. This is for compatibility with
nfdump 1.5.x and used to specify a single netflow source. See -n
-n <Ident,IP,base_directory>
Configures a netflow source named Ident and identified by source IP
address IP. The base directory for the flow files is
base_directory. If a sub hierarchy is specified with -S the final
directory is concatenated to base_directory/sub_hierarchy. Multiple
netflow sources can be specified. All data is sent to the same port
specified by -p. Note: You must not mix -n option with -I and -l.
Use either syntax.
-f <pcap_file>
Read netflow packets from a give pcap_file instead of the network.
This requires nfcapd to be compiled with the pcap option and is
intended for debugging only.
-s <rate>
Apply default sampling rate rate to all netflow records, unless the
sampling rate is announced by the exporting device. In that case the
announced sampling rate is applied. If <rate> is negative, this will
hard overwrite any device specific announced sampling rates.
-S <num>
Allows to specify an additional directory sub hierarchy to store the
data files. The default is 0, no sub hierarchy, which means the
files go directly in the base directory (-l). The base directory
(-l) is concatenated with the specified sub hierarchy format to form
the final data directory. The following hierarchies are defined:
0 default no hierarchy levels
1 %Y/%m/%d year/month/day
2 %Y/%m/%d/%H year/month/day/hour
3 %Y/%W/%u year/week_of_year/day_of_week
4 %Y/%W/%u/%H year/week_of_year/day_of_week/hour
5 %Y/%j year/day-of-year
6 %Y/%j/%H year/day-of-year/hour
7 %Y-%m-%d year-month-day
8 %Y-%m-%d/%H year-month-day/hour
-T <extension list>
Specifies the list of extensions, to be stored in the netflow file.
Regardless of the extension list, the following netflow data is
stored per record: first, last, fwd status, tcp flags, proto,
(src)tos, src port, dst port, src ipaddr, dst ipaddr, in(packets),
in(bytes). In addition nfcapd recognises the extensions as described
below. Some are valid for v5/v7/v9, but most of them make only sense
for v9. Any specified extensions which do not exist in the input
netflow records are ignored.
Extensions:
v5/v7/v9/IPFIX extensions:
1 input/output interface SNMP numbers.
2 src/dst AS numbers.
3 src/dst mask, (dst)TOS, direction.
4 line Next hop IP addr line
5 line BGP next hop IP addr line
6 src/dst vlan id labels
7 counter output packets
8 counter output bytes
9 counter aggregated flows
10 in_src/out_dst MAC address
11 in_dst/out_src MAC address
12 MPLS labels 1-10
13 Exporting router IPv4/IPv6 address
14 Exporting router ID
15 BGP adjacent prev/next AS
16 time stamp flow received by the collector
NSEL/ASA/NAT extensions
26 NSEL ASA event, xtended event, ICMP type/code
27 NSEL/NAT xlate ports
28 NSEL/NAT xlate IPv4/IPv6 addr
29 NSEL ASA ACL ingress/egress acl ID
30 NSEL ASA username
NEL/NAT extensions
31 NAT event, ingress egress vrfid
32 NAT Block port allocation - block start, end step and size
nprobe extensions
64 nprobe client/server/application latency"},
IMPORTANT: By default only extension 1 and 2 are selected
Extensions can be added/deleted by specifying a ',' separated list
of extension ids. Each id may be prepended by an optional sign +/-
to add or remove a given id from the extension list. Shortcuts:
The string 'all' means all extensions. The strings
'nsel' and 'nel' enable all NSEL or NEL extensions respectively.
Examples:
-T all Enables all possible extensions.
-T +3,+4 Adds extensions 3 and 4 to the defaults 1 and 2.
-T all,-8,-9 Set all extensions but 8 and 9
-T -1,4 Removes default extension 1 and adds extension 4
-T nsel Enables all required ASA?NSEL extensions
-T nel Enables all required nell extensions
Note: Only those tags in common with the exporting device and
enabled extensions at the collector side are stored into the data
files. A detailed list which v9 tags are mapped into which
extensions is given in the section NOTES
-t interval
Specifies the time interval in seconds to rotate files. The default
value is 300s ( 5min ).
-w Align file rotation with next n minute ( specified by -t ) interval.
Example: If interval is 5 min, sync at 0,5,10... wall clock minutes
Default: no alignment.
-x cmd
Run command cmd at the end of every interval, when a new file
becomes available. The following command expansion is available:
%f Replaced by the file name e.g nfcapd.200907110845 inluding any
sub hierarchy. ( 2009/07/11/nfcapd.200907110845 )
%d Replaced by the directory where the file is located.
%t Replaced by the time ISO format e.g. 200907110845.
%u Replaced by the UNIX time format.
%i Replaced ident string given by -I
-X Collect and embed extended statistics. Currently a port and bpp
histogram is embeded. Mostly experimental for now
-e Auto expire files at every cycle. max lifetime and max filesize are
defined using nfexpire(1)
-P pidfile
Specify name of pidfile. Default is no pidfile.
-D Daemon mode: fork to background and detach from terminal. Nfcapd
terminates on signal TERM, INT and HUP.
-u userid
Change to the user userid as soon as possible. Only root is allowed
to use this option.
-g groupid
Change to the group groupid as soon as possible. Only root is
allowed use this option.
-B bufflen
Specifies the socket input buffer length in bytes. For high volume
traffic ( near GB traffic ) it is recommended to set this value as
high as possible ( typically > 100k ), otherwise you risk to lose
packets. The default is OS ( and kernel ) dependent.
-E Print netflow records in nfdump raw format to stdout. This option is
for debugging purpose only, to see how incoming netflow data is
processed and stored.
-z Compress flows. Use fast LZO1X-1 compression in output file.
-V Print nfcapd version and exit.
-h Print help text to stdout with all options and exit.
RETURN VALUE
Returns 0 on success, or 255 if initialization failed.
LOGGING
nfcapd logs to syslog with SYSLOG_FACILITY LOG_DAEMON For normal
operation level 'warning' should be fine. More information is reported
at level 'info' and 'debug'.
A small statistic about the collected flows, as well as errors are
reported at the end of every interval to syslog with level 'info'.
EXAMPLES
All flows are sent to port 9995 from all exporters and stored into a
single file. All known v9 tags are taken.
nfcapd -z -w -D -T all -l /netflow/spool/allflows -I any -S 2 -P
/var/run/nfcapd.allflows.pid
All flows from 2 different exporters are sent to port 8877 and stored
in separate directory trees. All known v9 tags are taken. Input buffer
size is set to 128000 bytes
nfcapd -z -w -D -T all -p 8877 -n
upstream,192.168.1.1,/netflow/spool/upstream -n
peer,192.168.2.1,/netflow/spool/peer -S 2 -B 128000
Only accept from from a single exporter and only extension 3,4 and 5
are accepted. Run a given command when files are rotated and
automatically expire flows:
nfcapd -w -D -T 3,4,5 -n
upstream,192.168.1.1,/netflow/spool/upstream -p 23456 -B 128000
-s 100 -x '/path/command -r %d/%f' -P
/var/run/nfcapd/nfcapd.pid -e
NOTES
Multiple netflow sources:
Netflow data may be sent from different exporters to a single nfcapd
process. Use the -n option to separate each netflow source to a
different data directory. For compatibility with nfdump 1.5.x, old
style -l/-I options are still valid. In that case all flows from all
sources are stored in a single file. For high volume netflow streams,
it is still recommended to have a single nfcapd process per netflow
source.
The current v9 implementation of nfdump supports the following v9
elements: fields:
v9 element v9 ID Extension
NF9_LAST_SWITCHED 21 default
NF9_FIRST_SWITCHED 22 default
NF9_IN_BYTES 1 default
NF9_IN_PACKETS 2 default
NF9_IN_PROTOCOL 4 default
NF9_SRC_TOS 5 default
NF9_TCP_FLAGS 6 default
NF9_FORWARDING_STATUS 89 default
NF9_IPV4_SRC_ADDR 8 default
NF9_IPV4_DST_ADDR 12 default
NF9_IPV6_SRC_ADDR 27 default
NF9_IPV6_DST_ADDR 28 default
NF9_L4_SRC_PORT 7 default
NF9_L4_DST_PORT 11 default
NF9_ICMP_TYPE 32 default
NF9_INPUT_SNMP 10 1
NF9_OUTPUT_SNMP 14 1
NF9_SRC_AS 16 2
NF9_DST_AS 17 2
NF9_DST_TOS 55 3
NF9_DIRECTION 61 3
NF9_SRC_MASK 9 3
NF9_DST_MASK 13 3
NF9_IPV6_SRC_MASK 29 3
NF9_IPV6_DST_MASK 30 3
NF9_V4_NEXT_HOP 15 4
NF9_V6_NEXT_HOP 62 4
NF9_BGP_V4_NEXT_HOP 18 5
NF9_BPG_V6_NEXT_HOP 63 5
NF9_SRC_VLAN 58 6
NF9_DST_VLAN 59 6
NF9_OUT_PKTS 24 7
NF9_OUT_BYTES 23 8
NF9_FLOWS_AGGR 3 9
NF9_IN_SRC_MAC 56 10
NF9_OUT_DST_MAC 57 10
NF9_IN_DST_MAC 80 11
NF9_OUT_SRC_MAC 81 11
NF9_MPLS_LABEL_1 70 12
NF9_MPLS_LABEL_2 71 12
NF9_MPLS_LABEL_3 72 12
NF9_MPLS_LABEL_4 73 12
NF9_MPLS_LABEL_5 74 12
NF9_MPLS_LABEL_6 75 12
NF9_MPLS_LABEL_7 76 12
NF9_MPLS_LABEL_8 77 12
NF9_MPLS_LABEL_9 78 12
NF9_MPLS_LABEL_10 79 12
NF9_SAMPLING_INTERVAL 34 Sampling
NF9_SAMPLING_ALGORITHM 35 Sampling
NF9_FLOW_SAMPLER_ID 48 Sampling
FLOW_SAMPLER_MODE 49 Sampling
NF9_FLOW_SAMPLER_RANDOM_INTERVAL 50 Sampling
IP addr of exporting router 13
NF9_ENGINE_TYPE 38 14
NF9_ENGINE_ID 39 14
NF9_BGP_ADJ_NEXT_AS 128 15
NF9_BGP_ADJ_PREV_AS 129 15
collector received timestamp 16
32 and 64 bit are supported for all counters. 32it AS numbers are
supported.
IPFIX support is experimental. Due to lack of implementation of
sampling in many IPFIX exporters, sampling for IPFIX is not yet
supported.
The format of the data files is netflow version independent.
Socket buffer: Setting the socket buffer size is system dependent.
When starting up, nfcapd returns the number of bytes the buffer was
actually set. This is done by reading back the buffer size and may
differ from what you requested.
SEE ALSO
nfdump(1), nfprofile(1), nfreplay(1)
BUGS
No software without bugs! Please report any bugs back to me.
2009-09-09 nfcapd(1)