DragonFly On-Line Manual Pages
rrdbot.conf(5) DragonFly File Formats Manual rrdbot.conf(5)
NAME
rrdbot.conf - configuration files for rrdbotd(8)
DESCRIPTION
rrdbotd(8) is an SNMP polling daemon. It writes out the polled values to
an rrdtool(1) database. The configuration files describe what to poll and
where the resulting RRD files are.
The configuration files may be used by more than one program, for example
rrdbotd(8), or rrdbot-create(8). Some settings are shared between
programs, while many are program specific. Settings not recognized are
ignored.
An RRD file might only have one 'field' of values, or there may be
multiple values which are stored together. Each of the fields have a
name. Certain settings in the configuration file are used per field.
Where you see <field> in the documentaion below, substitute the
appropriate RRD field name.
SYNTAX
The general syntax of an RRD file is as follows:
# Comment
[header]
setting: a value here
field.setting: part of value
continuation of value
The configuration file is broken into blocks separated by headers. The
header sections each have different sets of options and are described
below.
The setting name (including a field name if necessary) is followed by a
colon and then the value. Values may be continued onto successive lines,
as long as those lines are indented with spaces or tabs.
Comments start with a # character at the leftmost margin.
GENERAL SETTINGS
These settings go under the [general] header in a configuration file.
rrd The location of the RRD file. If not specified these are
chosen automatically. See the FILE LOCATIONS topic below.
When specified this should be a full path.
[ Optional ]
POLL SETTINGS
Settings to control when and how the SNMP source is polled by rrdbotd(8).
These settings go under the [poll] heading.
interval The interval (in seconds) at which to retrieve the SNMP
values and store them in the RRD file.
[ Required for rrdbotd(8) ]
<field>.source
Specifies the SNMP source and OID in a URL format. The
<field> above should be replaced with the RRD field name.
Multiple xxxxx.source options can be specified if the RRD
file has multiple fields. The syntax of the SNMP url is as
follows:
snmp[version]://community@host[:port]/oid[?query=value]
The following are valid SNMP urls:
snmp://public@gateway.example.com/sysUptime.0
snmp2c://mycommunity@uplink.example.com/ifInOctets.2
snmp2c://mycommunity@example.com/ifInOctets?idDescr=eth0
snmp://public@www.example.com:10161/1.3.6.1.2.1.1.3.0
snmp://pub@two.example.com,one.example.com/sysUptime.0
See TABLE QUERIES for more info on how to use the query part.
See MULTIPLE HOSTS support for info on how to use multiple
hosts.
To test that your SNMP urls are correct you can use the
rrdbot-get(1) utility.
[ Required for rrdbotd(8) ]
timeout The timeout (in seconds) to wait for an SNMP response.
CREATE SETTINGS
These settings are used by the rrdbot-create(8) tool to automatically
create RRD files for you. Put these settings under the [create] header.
archive The archives of values you would like to keep in your RRD.
There can be multiple archives specified, separated by
commas. The syntax of an archive is as follows:
<count>/<unit> * <how-many> <units>
The example below describes three archives of "2 per minute
for 1 week", "4 per hour for 3 months", "3 per day for 1
year":
2/minute * 1 weeks, 4/hour * 3 months, 3/day * 1 year
[ Required for rrdbot-create 8 ]
cf The consolidation functions to use to consolidate RRD values
when archiving them. This applies to all fields in the RRD.
There can be multiple functions specified, separated by
commas. The valid functions are:
AVERAGE Average out the values when archiving them.
LAST Use the last value in the set to be archived.
MAX Use the maximum value in the set to be archived.
MIN Use the minimum value in the set to be archived.
[ Default: AVERAGE ]
<field>.max
The maximum value for the field. Use the character U to
specify that there is no maximum (unbounded).
[ Default: U ]
<field>.min
The minimum value for the field. Use the character U to
specify that there is no minimum (unbounded).
[ Default: U ]
<field>.type
The type of values that will be stored in this field. For
more info see the rrdcreate(1) manual. The types are:
ABSOLUTE Used for counters that get reset when read.
COUNTER For values that increment between reads.
DERIVE Used to measure rates of increase or decrease.
GAUGE For values that are current, for example the
temperature.
[ Default: ABSOLUTE ]
FILE LOCATIONS
To determine the default location for the configuration files and RRD
files run this command:
# rrdbotd -V
The configuration files for SNMP pollers are laid out in a directory
tree, with one file per RRD. Subdirectories can be used to organize the
configuration files. The contents of the configuration files are
described in rrdbot.conf(5).
By default the RRD files mirror the directory structure and names of the
configuration files, with an .rrd extension appended to the filename.
For example if your configuration files are in a structure like the
following:
/usr/local/etc/rrdbot/
gateways/
gateway-load.conf
gateway-traffic.conf
temperature/
inside-temperature.conf
outside-temperature.conf
machine-load.conf
Then the default RRD files would be in a similar directory structure:
/var/db/rrdbot/
gateways/
gateway-load.conf.rrd
gateway-traffic.conf.rrd
temperature/
inside-temperature.conf.rrd
outside-temperature.conf.rrd
machine-load.conf.rrd
The default location for an RRD file can be overridden by using the rrd
option in the configuration file.
Once you have configuration files in place, you can use the
rrdbot-create(8) tool to create the needed RRD files in the appropriate
places.
MULTIPLE AGENTS
rrdbotd(8) supports failover between multiple agents. If an SNMP query
fails on one agent or a value is not found when querying an agent, then
it will switch to another configured agent.
When combined with a query (see TABLE QUERIES) you can use this feature
to search for a given value in a table on one of multiple agents.
To use failover, simply use multiple host names with commas (without a
space) separating them. For example:
snmp://public@two.example.com,one.example.com/sysUptime.0
TABLE QUERIES
rrdbotd(8) can query a value that corresponds to a certain row in an SNMP
table. On many SNMP agents the indexes of rows in tables are not fixed,
and this allows you to retrieve a certain value no matter what row of the
table it is on.
Add the OID and value you want to search for in the table to the end of
the SNMP URL. Only one query value is supported.
For example to get the outbound packet count on the 'eth0' interface, you
would use:
snmp://public@example.com/ifInUcastPkts?ifDescr=eth0
SEE ALSO
rrdbotd(8), rrdbot-create(8), rrdbot-get(1), rrdtool(1)
AUTHOR
Stef Walter <stef@memberwebs.com>
rrdbot August, 2006 rrdbot